Finned heaters

Made up of an armored element formed into a pin or a paper clip, these resistors are fitted with crimped rectangular fins or spiral fins .

The finned elements make it possible to install, according to the air speeds and set temperatures, high power densities in forced convection.
Equipped with threaded connections, the finned resistors are installed in convectors, rectangular or circular ventilation ducts (see heating batteries), but also discharge resistors, etc.

We offer many standard references available from stock or special products made according to your specifications.

Finned heaters

Made up of an armored element formed into a pin or a paper clip, these resistors are fitted with crimped rectangular fins or spiral fins .

The finned elements make it possible to install, according to the air speeds and set temperatures, high power densities in forced convection.
Equipped with threaded connections, the finned resistors are installed in convectors, rectangular or circular ventilation ducts (see heating batteries), but also discharge resistors, etc.

We offer many standard references available from stock or special products made according to your specifications.

Rectangular fin resistors

Technical characteristics

Our aluminum-zinc finned resistors are designed to be perfectly suited to heating air by natural or forced convection in industrial fields (ovens, ovens, air conditioning heating, etc.).

We also offer all stainless steel finned resistances when high temperature conditions require it (humid or slightly corrosive environment).

Made up of a shielded element formed into a hairpin on which rectangular fins 25×50 mm or 40×70 mm are crimped, our standard resistors have a specific load of approximately 4 W / cm².

They operate in natural convection up to 140 ° C.
We recommend a minimum flow rate so that the working temperature does not exceed 200 ° C for aluzinc models, 300 ° C for all stainless steel models. The temperature on the terminals must never exceed 100 ° C.

Product range

Stock range:

    • 2 ranges kept in stock: aluminum-zinc alloy or stainless steel fins
    • Crimped rectangular fins, dimensions 25×50 mm or 40×70 mm, depending on the model
    • Shaped armored element, made of stainless steel
    • Electrical connection by flat clamp terminals (aluminum-zinc models), or by threaded rod (stainless steel models)
    • Resistor supplied with fixing fittings and nuts.
    • Power range: 500 W to 3 kW
    • Supply voltage: 230 V mono.
    • Resistors sold alone, without cover

.

In addition, we offer accessories for rectangular finned resistors:

  • Mounting brackets
  • connection cover

.

Custom-made

We can manufacture resistors to measure, according to your specifications. This list is not exhaustive, carried out following a feasibility study. Do not hesitate to consult us:

    • Total length except standard
    • Non-heating length, close to the connection, made to measure
    • Other type of connection
    • Specific sleeve
    • End bracket ….
Regulatory characteristics
  • Manufacturing according to standard EN 60335-1
  • Wattage tolerance: + 5% -10%
  • Leakage current< 0.75 mA / kW
  • REACH and RoHS compliant
Additional Products

In addition to the finned resistors, we offer you the necessary equipment for its electrical supply and the regulation of your process:

Downloadable documents

Standard rectangular fin resistors

Spiral fin resistors

Technical characteristics

Made up of a straight armored element on which a steel or stainless steel strip has been wound, the spiral fin resistors can be bent on demand and take the most complex shapes. This technique allows high power densities (approximately 7W / cm²).

Possibility of greater center distance with rectangular fins.

Spiral fins are generally installed in batteries, ovens, ovens, etc.

Product range

Standardized range:

    • Shielded element shaped as a hairpin, in Ø 10 mm stainless steel AISI 321 stainless steel.
    • Spiral 304 stainless steel fins, diameter 30 mm.
    • Fittings: protected steel crimped M14X100 L15, center distance 70 mm.
    • Electrical connection by M4 threaded terminals.
    • Resistor supplied with fittings, gaskets and nuts.
    • Power range: 1 kW to 3 kW
    • Load: 6.5 W / cm².
    • Supply voltage: 230 V mono.
    • Resistors sold alone, without cover.

Custom-made

We can manufacture resistors to measure, according to your specifications. This list is not exhaustive, carried out following a feasibility study. Do not hesitate to consult us:

    • Total length except standard
    • Non-heating length, close to the connection, made to measure
    • Other type of connection
    • Specific sleeve
Regulatory characteristics
  • Manufacturing according to standard EN 60335-1
  • Wattage tolerance: + 5% -10%
  • Leakage current< 0.75 mA / kW
  • REACH and RoHS compliant
Additional Products

In addition to the finned resistors, we offer you the necessary equipment for its electrical supply and the regulation of your process:

Downloadable documents

Standard Spiral Finned Resistors

Additional Products

Cables
& accessories

Cables & Accessories

Find out more

Temperature Sensors

Temperature Sensors

Find out more

Regulation and temperature sensors

Temperature Control

Find out more
logo-titre-blanc-2Other models of armored resistors