Temperature Control

Temperature management is an essential parameter in the success of a thermal process. If the heating element is important, it is imperative to manage it with a suitable control system.
This not only to obtain the desired precision, but also to optimize the service life of the heating elements.

In addition to our heating solutions , we can help you determine the most suitable model for your process.

Temperature Control

Heat management is an integral part of an industrial process: it must be controlled with a suitable temperaturte control system.

In addition to our heating solutions , we can help you determine the appropriate model.

Appropriate teperature control also makes it possible to optimize the service life of the heating elements.

Depending on the use, we offer different control systems, precision and type of control: from component to turnkey system, in kit or integrated in a complete electrical cabinet integrating power supply, control, safety management …

Depending on the need, we are able to offer different regulation systems, ranging from components to turnkey systems, from spare parts to elements integrated into a box and from control to safety management.

Controllers - Solid State Relays

Technical characteristics

Digital PID controllers

The 48CSP2E (black front) or 48CSP3A (red front) temperature controllers operate in PID mode, allowing precise regulation. They are equipped with a logic output for controlling static relays and relay outputs for electromechanical contactors and alarms.

Built-in controllers, format 48×48 mm , they are equipped with a double display.
Their universal input accepts thermocouples, PT100 probe, 4-20 mA, 0-10 V.

  • 48CSP2E Temperature Controller: 2 outputs (1 logic + 1 relay)
  • 48CSP3A Temperature Controller: 3 outputs (1 logic and 2 relay outputs)

Programmable versions or versions with additional functions (Retransmission of measurement mesure value, remote sepoint, LBA, HBA, etc.) are also available, do not hesitate to contact us.

Solid State Relays

Solid-state relays, electronic power units, allow rapid switching of electrical heating elements without the risk of arc wear or destruction of the switch. Controlled by digital controllers, they make it possible to obtain stability and a very high precision of control.

2 models are available as Standard Stock: 25 A or 40 A , for a voltage between 24 and 480 Vac.
Other models can switch higher intensities, up to 120 A.

ON/OFF Temperature Controllers

Models in the 48C200 series (grey front) operating in ON/OFF mode, can be used as main controller or as a safety regulator, on the front or in the back of the cabinet.

Panel mounting controllers, casing 48 x 48 mm , they are suitable for piloting electromechanical contactors.
Measurement input for J or K thermocouple depending on the model.

Product range

Controllers

  • 48C200 series controller
    • Standard Stock Models: 48C201 (range 0 … 200 ° C), 48C203 (range 200 … 1200 ° C)
    • Casing: 48 x 48 mm
    • Regulation mode: TOR (ON/OFF)
    • Thermocouple input: J (48C201) or K (48C203).
    • Output: relay, breaking capacity 3 A 230 Vac. Connection by screw terminal block.
    • Indicator lights indicating the heating and resting cycles.
    • Power supply: 115 or 230 Vac switchable.

  • 48CSP2E controller
    • Standard Stock model
    • Casing: 48 x 48 mm
    • Regulation mode: ON/OFF, P, PD, PID in heat and cool control. Control with auto-adaptive function.
    • Universal programmable input: thermocouples, Pt100, 4 – 20 mA, 0 – 10 V.
    • 1 logic output 24 Vdc ± 10% (10 V min in 20 mA), for solid state relay
    • 1 relay output 5 A 250 Vac / 30 Vdc resistive (configured as standard, in alarm)
    • Configurable alarms
    • Connection by screw terminal block.
    • Indicator lights for output status, alarm, setpoint, auto-adjustment
    • Power supply: switchable 100 to 240 Vac, 50 – 60 Hz
    • The +: Power supply for transmitter 15 … 24 V, not stabilized, 30 mA

  • 48CSP3A regulator
    • Standard Stock model
    • Casing: 48 x 48 mm
    • Control mode: TOR, P, PD, PID in heat and cool control. Control with auto-adaptive function.
    • Universal programmable input: thermocouples, PT100, 4 – 20 mA, 0 – 10 V.
    • 1 logic output 24 Vdc ± 10% (10 V min in 20 mA), for solid state relay
    • 2 relay outputs 5 A 250 Vac / 30 Vdc resistive (configured as standard, in alarm)
    • Configurable alarms
    • Connection by screw terminal block.
    • Indicator lights for output status, alarm, setpoint, auto-adjustment
    • Power supply: switchable 100 to 240 Vac, 50 – 60 Hz
    • The +:
      – 2 relay outputs
      – Large format display
      – EASY configuration mode, for quick access to basic parameters

Solid state relays

    • Standard Stock models: RS25480, RS40480
    • Nominal current: 25 A (Reference RS25480) or 40 A (Reference RS40480), at 40 ° C
    • Input control by logic signal
    • LED ignition indicator
    • Nominal voltage: 480 Vac (max range 24 … 530 Vac)
    • Control voltage: 6 … 32 Vdc
    • Frequency: 50 – 60 Hz
    • DIN panel mounting
    • Operating temperature: 0 to 80 ° C, depending on the dissipation curves
Downloadable documents

Controllers

Solid state relays

Thermostats - Bimetallic Power Regulators

Technical characteristics

Thermostats

Single-pole bulb and capillary control thermostats operate on the principle of expansion of the liquid contained in the bulb brought to measure the temperature.

They make it possible to regulate in ON/OFF control a set temperature marked on the button, according to a differential of rearmament (interval of measurement).

Used as a control or safety device, they make it possible to dispense with the use of a temperature sensor, which is already integrated.

Operating range of standard stock models: 4…40°C , 0…90°C , 30…110°C , 50…300°C.

Bimetallic Power Regulators

The powers regulators make it possible to control the heating in open loop, ie by manually adjusting the power of the heating elements. They cyclically cut the power supply to the heating elements, over specified durations for each graduation of the adjustment button, which makes it possible to modulate the average power.

Connected between the power supply and the heating resistance, they eliminate the need for a temperature sensor.

Operating voltage of standard stock models : 24 Vac or 230 Vac.

Product range

Thermostats

Features common to thermostats:

    • Terminals: 6.3 x 0.8 tabs
    • Knob graduated 10 ° C in 10 ° C, mounted on an axis (bare knob for 4 … 40 ° C)
    • Single pole changeover contact, breaking capacity at opening: 16 A 250 Vac, 50 – 60 Hz (resistive load)
    • Case (L x W x H): 43 x 35 x 29 mm (excluding terminals)

  • Thermostat, range +4… + 40 ° C
    • Copper bulb Ø6 mm, length 135 ± 5 mm.
    • Copper capillary, length 1500 mm
  • Thermostat, range +0… + 90 ° C
    • Stainless steel bulb Ø 6 mm, length 98 ± 5 mm
    • Stainless steel capillary, length 1500 mm
  • Thermostat, range +30… + 110 ° C
    • Ø6mm stainless steel bulb, length 115 ± 5 mm
    • Stainless steel capillary, length 1500 mm
  • Thermostat, range +50… + 300 ° C
    • Ø3mm stainless steel bulb, length 135 ± 5 mm
    • Stainless steel capillary, length 1500 mm

Bimetallic Power Regulators

Features common to thermostats:

    • Terminals: 6.3 x 0.8 tabs
    • Adjustment by graduated knob, mounted on an axis
    • Breaking capacity: 12 A 250 Vac, 50 – 60 Hz (resistive load), auxiliary contact of pilot light
    • Fixing by threaded barrel and 2 anti-rotation lugs
    • Case (L x W x H): 50 x 42 x 39 mm (off axis)

  • Dosing, supply voltage: 24 Vac (DE24)
  • Dosing, supply voltage: 230 Vac (DE220)
Downloadable documents

Thermostats

Bimetallic Power Regulators

Control Panels and Cabinets

Technical characteristics

In addition to our heating solutions, we define and manufacture control panels intended for power supply and temperature regulation.

  • We offer a standard range, of several powers, available in stock.
    These models, supplied with 230 Vac single-phase or 400V three-phase, meet the needs of low power up to 27 kW.
  • We carry out custom-made products according to your specifications. From the portable model for laboratory benches to systems with several control zones, our panels and cabinets can be equipped with datas recorders, HMI or communication interfaces (RS485, field bus, etc.)
  • Our devices are defined by our design office then assembled, wired and tested in our workshops in Normandy.
  • Cabinets and panels comply with the NFC 15-100 standard.
Product range
  • Standard range , ready-to-use boxes (stock models):
    • Painted sheet metal enclosure, with door, IP 55
    • Standard range: 5 kW under 230 Vac single-phase, to 27 kW under 400 Vac three-phase
    • 1 control zone, equipped with a 48CSP2E dual display digital controller, accepting thermocouples such as PT100 sensors
    • Power ON indicator
    • Solid state relays operating as zero cross switching as not to induce disturbances to the electrical network
    • Separation of power / control circuits by transformer
    • Cable glands for power, sensor and power supply
  • Custom manufacturing , following feasibility study
    • IP rate
    • UL Standard
    • Tropicalized
    • Air-conditioned
    • Automation

Downloadable documents

Standard Panels :

Additional Products

Temperature Sensors

Temperature Sensors

Find out more

Cables
& accessories

Cables & Accessories

Find out more
logo-titre-blanc-2Back to product line