Internet Explorer / Edge Legacy browser compatibility

It seems that you are using an expired version of your browser, you can still browse our site, however display problems may appear.
We advise you to update your browser in order to be able to take full advantage of our site or to change your internet browser .

+33 (0)2 32 62 34 20
Search
Close this search box.

Heating of IBC / IBC Containers and Accessories for Drums

Other accessories

Heated tarpaulins for IBC container

Technical characteristics

Tarpaulins designed for heating products stored in 1000 liter tanks .

Resistances equipped with 2 to 3 independent heating zones depending on the model, with their own regulation.

  • This system makes it possible to adapt the heating power to the volume of liquid located in the IBC, by cutting off the heating of the upper zones as soon as the level of liquid is lower than the latter.
  • the different regulation zones allow an even temperature distribution over the entire height of the tarpaulin.

.

  • Regulation by adjustable thermostat. 2 ranges available: 0 to 40°C or 0 to 90°C , depending on the model;
  • Low load allowing the heating of particularly sensitive products. (> 0.1W/cm2)
  • Heating element fixed on a water-resistant teflon-coated polyester frame, and protected by 2 polyester frames.
  • Heating by 2 to 3 independent circuits , 1000W each , depending on models.
  • Thermal insulation
  • Tightening by adjustable strap in length and locking clips.
  • Double electrical insulation, requiring no earth connection
  • Power supply: 230 Vac mono.
  • Cables, rubber insulated under neoprene sheath, length 3 or 4 m depending on the model.
  • IP40 protection

.

In addition to the covers, an insulated cover COUV.CFPL can be positioned on top of the IBC, protecting it from heat loss

Product range

On stock range

  • Dimensions (H x W): 1000 x 4400mm, identical for all models
  • Voltage: 230V single phase for each circuit

.

  • CFPL 1001:
    • 2 circuits of 1000W
    • 2 adjustable thermostats from -5°C to +40°C

.

  • CFPL 1002:
    • 2 circuits of 1000W
    • 2 adjustable thermostats from +20°C to +90°C

.

  • CFPL 1003:
    • 3 circuits of 1000W
    • 3 adjustable thermostats from +20°C to +90°C

.

  • COUV.CFPL: insulating cover, with cut-out to facilitate emptying.
Regulatory characteristics

Manufacture according to standard EN 60335-1 :

  • Wattage tolerance: + 5% -10%
  • Leakage current< 0.75 mA / kW
Additional Products

The use of heating band heaters requires the installation of complementary products:

Downloadable documents

Downloadable sheets and instructions :

  1. Technical data sheet
  2. Instructions for use
  3. Principle drawing

Insulation blankets for drums

Technical characteristics
  • Insulating jacket to maintain the temperature after heating the drum. Blanket used in addition to the heating base, to reduce the heating time.
  • Reinforced thermal insulation thanks to a thick layer of fiberglass.
  • Outer face of strong thickness, in Cordura®, resistant to tearing.
  • Inner side in polyester coated with a layer of Teflon.
  • Opening provided for the introduction of a pump or a thermometer, which can be folded down to limit heat loss.
Product range
  • Standard range
    • Cover for barrels: 25, 50 and 105 litres.
Regulatory characteristics

Manufacture according to standard EN 60335-1 :

  • Wattage tolerance: + 5% -10%
  • Leakage current< 0.75 mA / kW
Downloadable documents

Immersion heater heaters

Technical characteristics
  • Heating of non-aggressive solutions or liquids such as fatty acid, methyl bromide, demineralized water, mineral oils, glycerine…
  • Armored tube diameter 8mm, in AISI 321 stainless steel.
  • P-67 resin handle.
  • Electrical connection by cable, 2 phases + earth rubber insulated under neoprene outer sheath (T°max: 60°C).
  • Protection index: IP 20.
Product range
  • Standard range:
    • Supply voltage: 230V single phase
    • Heating element shaped like 2 hairpins for the THERMFUT 1000 and 1500 models, and a single hairpin for the THERMFUT 1200 model

Models:

THERMFUT1000:

  • Minimum diameter: 56.5mm
  • Plunging length: 1170mm
  • Heating length: 150mm
  • Power: 1000W

THERMFUT1500:

  • Minimum diameter: 56.5mm
  • Plunging length: 1170mm
  • Heating length: 150mm
  • Power: 1500W

THERMFUT1200:

  • Minimum diameter: 24mm
  • Plunging length: 840mm
  • Heating length: 444mm
  • Power: 1200W
Regulatory characteristics

Manufacture according to standard EN 60335-1 :

  • Wattage tolerance: + 5% -10%
  • Leakage current< 0.75 mA / kW

Additional Products

The use of heating band heaters requires the installation of complementary products:

Downloadable documents

Downloadable sheets and instructions :

Additional Products

Temperature Sensors

Temperature Sensors

Find out more

Temperature Controllers

Temperature Controllers

Find out more

Cables
& accessories

Cables & Accessories

Find out more
logo-titre-blanc-2Other articles for heating drums and IBCs